Question
Directions: Use this worksheet to record your answers to the questions or problems
for the ADA Ramp portfolio.
Where indicated, draw figures on a blank sheet of paper or on a sheet of graph
paper. Be sure to label each sheet so that your teacher knows which answer goes
with which question. You can scan these figures and submit them as individual
documents with your portfolio worksheet, or you can take pictures of them and
insert the pictures on the portfolio worksheet.
Day 1
Design a wheelchair ramp for an entrance that is between 12 and 30 inches above
ground level. Your design must meet ADA guidelines. To submit your design, do the
following:
step by step drawing
for the ADA Ramp portfolio.
Where indicated, draw figures on a blank sheet of paper or on a sheet of graph
paper. Be sure to label each sheet so that your teacher knows which answer goes
with which question. You can scan these figures and submit them as individual
documents with your portfolio worksheet, or you can take pictures of them and
insert the pictures on the portfolio worksheet.
Day 1
Design a wheelchair ramp for an entrance that is between 12 and 30 inches above
ground level. Your design must meet ADA guidelines. To submit your design, do the
following:
step by step drawing
Answers
GPT-4o mini
Certainly! Below is a step-by-step guide to designing a wheelchair ramp that meets ADA guidelines for an entrance between 12 and 30 inches above ground level. Here’s how you can create the drawing:
### Step 1: Gather Materials
- Blank paper or graph paper
- Ruler
- Pencil
- Eraser
### Step 2: Understand ADA Guidelines
1. **Slope**: The ADA recommends a slope of 1:12 for wheelchair ramps. This means that for every inch of vertical rise, there should be at least 12 inches (1 foot) of ramp run.
2. **Width**: The ramp must be at least 36 inches wide.
3. **Landing**: A flat landing is required at the top and bottom of the ramp, measuring at least 5 feet by 5 feet.
4. **Surface**: The ramp surface must be stable, firm, and slip-resistant.
### Step 3: Determine Ramp Height
- **Height**: Choose a height within the range of 12 to 30 inches. For example, let’s use a height of 24 inches.
### Step 4: Calculate Ramp Length
Using the 1:12 slope:
- **Run = Height × 12**
- Run = 24 inches × 12 = 288 inches (24 feet)
### Step 5: Draw the Ramp
1. **Draw the End Points**:
- Start by marking the height of the entrance (24 inches up) on the left side of your paper.
- Mark the bottom of the ramp at ground level (0 inches).
2. **Draw the Slope**:
- Using a ruler, draw a diagonal line from the bottom point (0 inches) to the top point (24 inches). This line will represent the incline of the ramp.
3. **Design the Width**:
- From the diagonal line (ramp), mark 18 inches on either side of the slope to represent the width of the ramp (total width = 36 inches).
4. **Add Landings**:
- At the top of your ramp, create a flat, horizontal section that measures at least 60 inches (5 feet) wide and 60 inches deep. Do the same at the bottom of the ramp.
### Step 6: Label Your Drawing
- Mark important dimensions on your drawing:
- Ramp height (24 inches)
- Ramp length (288 inches)
- Ramp width (36 inches)
- Landing dimensions (5 feet by 5 feet at each end)
### Step 7: Review
Make sure your ramp adheres to all ADA guidelines regarding slope, width, and landings.
### Draw Your Ramp
Once you have completed all the steps above, take a clear picture or scan your drawing and label it as “ADA Ramp Design”.
### Submission
Make sure to organize your worksheet with this drawing along with any other required documentation, and submit it according to your teacher's instructions.
If you have any specific requests for drawing or additional design features, feel free to ask!
### Step 1: Gather Materials
- Blank paper or graph paper
- Ruler
- Pencil
- Eraser
### Step 2: Understand ADA Guidelines
1. **Slope**: The ADA recommends a slope of 1:12 for wheelchair ramps. This means that for every inch of vertical rise, there should be at least 12 inches (1 foot) of ramp run.
2. **Width**: The ramp must be at least 36 inches wide.
3. **Landing**: A flat landing is required at the top and bottom of the ramp, measuring at least 5 feet by 5 feet.
4. **Surface**: The ramp surface must be stable, firm, and slip-resistant.
### Step 3: Determine Ramp Height
- **Height**: Choose a height within the range of 12 to 30 inches. For example, let’s use a height of 24 inches.
### Step 4: Calculate Ramp Length
Using the 1:12 slope:
- **Run = Height × 12**
- Run = 24 inches × 12 = 288 inches (24 feet)
### Step 5: Draw the Ramp
1. **Draw the End Points**:
- Start by marking the height of the entrance (24 inches up) on the left side of your paper.
- Mark the bottom of the ramp at ground level (0 inches).
2. **Draw the Slope**:
- Using a ruler, draw a diagonal line from the bottom point (0 inches) to the top point (24 inches). This line will represent the incline of the ramp.
3. **Design the Width**:
- From the diagonal line (ramp), mark 18 inches on either side of the slope to represent the width of the ramp (total width = 36 inches).
4. **Add Landings**:
- At the top of your ramp, create a flat, horizontal section that measures at least 60 inches (5 feet) wide and 60 inches deep. Do the same at the bottom of the ramp.
### Step 6: Label Your Drawing
- Mark important dimensions on your drawing:
- Ramp height (24 inches)
- Ramp length (288 inches)
- Ramp width (36 inches)
- Landing dimensions (5 feet by 5 feet at each end)
### Step 7: Review
Make sure your ramp adheres to all ADA guidelines regarding slope, width, and landings.
### Draw Your Ramp
Once you have completed all the steps above, take a clear picture or scan your drawing and label it as “ADA Ramp Design”.
### Submission
Make sure to organize your worksheet with this drawing along with any other required documentation, and submit it according to your teacher's instructions.
If you have any specific requests for drawing or additional design features, feel free to ask!